Description

Odroid-HC4 Home Cloud 4GB RAM Amlogic S905X3 1.8GHz Quad Core

Download Odroid-HC4 Resources

Just like the Odroid-C4, the 1.8Ghz Amlogic S905X3 ARM Cortex-A55 Quad-Core processor with Mali G31 MP2 Graphics Processing Unit is also featured by the HC4. The HC4 is grounded on the Home Cloud platform. This HC4 comes with an SPI 16MiB flash chip with Petitboot support. This board’s memory is DDR4 4GB RAM. 

Note: This Odroid-HC4 Version DOES NOT include OLED 

What is new with Odroid-HC4 

Instead of USB3.0 to SATA, the Odroid-HC4 has a solid SATA bridge solution (PCIe to SATA). This way, the Odroid-HC4 backs two SATA storage docks. Along with this board comes a transparent case with cutouts for ports and board interfaces. 

Specifications of Odroid-HC4 Home Cloud 

• Processor 

• Amlogic S905X3 12nm 
• Architecture: ARMv8-A with Crypto and Neon extensions 
• Mali-G31 MP2 GPU (650MHz) 4x Execution Engines 
• 32 KB L1 instruction cache, 128 sets 4-way set associative, 1 processor shares 64 byte lines 
• 32 KB L1 data cache, 128 sets 4-way set associative, 1 processor shares 64 byte lines 
• 512KB L3 data cache, 512 sets 16-way set associative, 4 processors share 64 byte lines 

• RAM 

• 4GiB DDR4 
• Low Power Design: 1.2Volt 
• But width: 32-bit 
• Data Rate: 2640 MT/s 
• Grade: PC4-21333 

• Storage 

• 1x Micro SD Slot (Attuned with DS/HS mode and supports UHS-1 SDR104) 

• Networking 

• 1x RJ45 GbE LAN Port | supports 10/100/1000 Mbps 
• Amber LED: 1000Mpbs connection data traffic indicator 
• Green LED: 100Mpbs connection data traffic indicator 
• RTL8211F Realtek Ethernet Transceiver 

• Cooling Fan 

• A Hydraulic Bearing Fan 
• Air Pressure: 0.053 in H2O 
• Air Flow: 4.3 CFM 
• Noise Level: 23.9 dBA 
• Current Rating: 100 mA 
• Voltage Rating: 5V 
• Maximum Rotations Per Minute (RPM): 4000 Rotations 
• Connector and Wire: 1.25mm Pitch 4-Pin, 80mm 
• Dimensions: 4cm x 4cm x 1.06cm 

• External Input / Output 

• HOST USB 2.0 Port (x1) 
• SATA Connectors (x2) 
• UART Serial Debug Console (x1)

• General 

• IR receiver for infrared remote control 
• System Indicator LEDs 
  • RED LED for PWR (DC Power Connected) 
  • BLUE (Flashes when Kernel is running) 

• Video 
• 1x HDMI 2.0 Port with HDR, EDID, CEC | up to 4K @ 60Hz 
• Audio 
• 1x HDMI Digital Audio Output 
• Heatsink  
• A passive heatsink on the processing unit 
• Dimensions: 4cm x 3.2cm x 1cm Power 

• 1x DC Power Jack: 5.5mm (negative / outer) and 2.1mm (positive / inner) diameter 
• 5V ~ 15.5V DC Input 
• 15V / 4A DC Power Adapter Suggested (Not Included)

• Power Consumption with 2x HDDs (ST2000DM006) 

• IDLE Mode: About 5.88 W (when HHD is in Spin-Down) 
• Suspend Mode: About 0.29 W
• Active Mode: About 15.59 W (while using SAMBA) 

• Form Factor 

• Dimensions of HC4 Board: 9.05cm x 8.4cm x 2.5cm  
• Weight of HC4 (including the case, fan, and heatsink): 280 grams | 0.28 kg 

Odroid-HC4 Software Compatibility

Petitboot can automatically locate the Operating System on the SD-Card, SSD, or HDD. In case the SD-Card is not attached, Petitboot uses the attached SSD or the HDD to boot the HC4. This possible if the Operating System is installed on any of the above-mentioned connected storages.  

Ubuntu and Debian Operating Systems are compatible with the preinstalled Operating System Image from Hardkernel. Ubuntu or Debian Netboot installers can be used too. 

The HC4 supports Linux Kernel’s following versions: 

• Version 4.9.230 or higher of Hardkernel Stock Operating System
• Version 5.8 or higher of Mainline Kernel (unofficial)